Sako L461 varmint stock - DIY- Now 20/222

[B4408]

I bought a sporter 222mag last year and have decided to give it a makeover. One of my goals for this year was to shape a walnut stock and checker it. Barry B had a piece of walnut I bought and will be glad to see it get used. I've made a couple of other stocks which are on this site but only used some rosewood I laminated, low cost and easy way to learn. So time to get serious.
This will be a 20/222 when the barrel gets done, in a varmint profile. Rather than open up the original stock that is in good condition was another reason to have a go.
I square up the sides and top first so I can get some reference points. Then drill action bolt holes on drill press. Then use a router and jig I made to get the bulk wood removed. Saw the idea for the jig on line, I use to do a similar method with the blank clamped to the side of my bench and various straight edges for guides. Jig is much easier.
Here are a few pics from todays start.

Sako 222mag sporter

20200927_111741 A.jpg (181.21 KiB) Viewed 29547 times

Barry's blank. Bit of grain

20211024_112000 A.jpg (89.23 KiB) Viewed 29547 times

Expensive shavings. Through the thicknesser - 54mm

20211024_113847 A.jpg (82.03 KiB) Viewed 29547 times

in the jig for routing

20211024_154624 A.jpg (128.45 KiB) Viewed 29547 times

Action inlet started

20211024_174436 A.jpg (89.45 KiB) Viewed 29547 times

Long way to go but will do a little bit after work each day.

Bruce

[Branxhunter]

Watching with a LOT of interest. Nice chunk o wood.

Marcus

[barryb]

There's more than Marcus watching this project with lots & lots of interest Bruce - looking good & congratulations on getting it up & running.

[MISSED]

Ditto

[MISSED]

Ditto

[barryb]

[/I TOOK A PICTURE TODAYb]
Almost a twin to that one of Bruce's -so lonely in the shed , just waiting for a nice home , somewhere.

[Ned Kelly]

G'day All,
here's the link for an online DIY stock, probably the same as the one Bruce saw.
Some good ideas in this link
https://forum.accurateshooter.com/threa ... j6x54VhE78

Enjoy. Fyi Keep up the great work Bruce!
Cheerio Geoff

[B4408]

Ned, that was the one I copied the idea from.

Barry, tempting to have a matched pair but I would have to buy another Sako.

A bit of progress. Lots of time spent but not much to show. Have the action glued in. Used some masking tape to give clearance on front and sides of recoil lug and rear of tang.
Should pop out easy tomorrow, never had one not release but some have you thinking.....

glued in.

20211029_174559 A.jpg (116.98 KiB) Viewed 29499 times

Going to have a look at the trigger while it is off the action. Its ok now but a little lighter would be good.

Bruce

[barryb]

Never ceases to amaze me Bruce - please keep your phone lines operative as I'm heading over to the gunsafes to have a look - pretty sure there's still a couple of Sakos around over there. : & I haven't been doing much shooting of late.

[MISSED]

I have thined the Herd considerably Barry I have 3 left

[B4408]

Finished for the weekend.
After a lot of sitting and contemplating I got stuck into it and hoped that a rifle stock starts coming out of the piece of wood. I 3D printed a few templates for butt and floorplate to give some guidance and also draw lines everywhere then ignore most of them.
I use the circular saw and jigsaw to remove the bulk easy bits. Then hand planes to remove some corners. I do most of the roughing out with a 4" belt sander and 80 grit belt. With a bit of care and lots of stopping and eyeing lines you can get pretty close to final shape with the powered hand tools.

basic lines and angles

20211030_110656a.jpg (126.73 KiB) Viewed 29477 times

electric plane thins it down quick

20211031_092725 A.jpg (167.69 KiB) Viewed 29477 times

Hand planes also used

20211031_095604 A.jpg (133.29 KiB) Viewed 29477 times

floorplate inlet with router and template and started with belt sander

20211031_153418 A.jpg (91.03 KiB) Viewed 29477 times

after the belt sander

20211031_163132 A.jpg (182.79 KiB) Viewed 29477 times

Now time for the rasps and files to shape the pistol grip, flatten and smooth down the sanded butt.
I wet the stock to see the colour, the wife was impressed. Its going to show some nice grain. Good one Barry
Lots still to do.

Bruce

[MISSED]

I am impressed

[dashooter]

Very nice Bruce. Great work with the tools.


Sent from my iPhone using Tapatalk

[daisy]

Looking good Bruce.
With my ham fists I'd have at least 3 pieces by now.

[barryb]

Excellent stuff Bruce - please don't forget to keep your drawing & information . When you get a chance could you PM me your posting address , thanks.