Winchester 9422 extraction issue

Gunsmithing & DIY forum for everyone. Enjoy!
Post your projects, questions and advice here.
User avatar
Keachie
.222 Remington
Posts: 333
Joined: Fri Jan 20, 2017 10:21 pm
Favourite Cartridge: .223
Location: Branxholm Tasmania

Winchester 9422 extraction issue

Post by Keachie »

So my winchester lever action is having extraction issue where it won't pull out the spent round. But if put pressure on the the claw with my finger it pulls the round.

After reading a bit on how to pull the action apart the is ment to be 2 springs the run at a 90 degree angle to the base of the extractor claw and these can get tied up on each other reducing spring tension on the claw hence issue (if this is indeed the issue).

My question is should I have a crack at fault finding and repairing the issue or should I just take it to my LGS?

Sent from my SM-A520F using Tapatalk

User avatar
The Raven
Ultimate AusVarminter
Posts: 5945
Joined: Tue Feb 08, 2011 2:35 pm
Favourite Cartridge: .270 Win
Location: The Cloud

Re: Winchester 9422 extraction issue

Post by The Raven »

If you think you're handy enough on the tools it's worth a try. However, as soon as you strike any problems (particularly those involving forcing stuff) pack it all up and visit a gunsmith.

Hint: If you're pulling apart anything that may launch small springs, screws, and the like across the room then disassemble the part in a plastic bag. That will capture any errant parts and save a lot of floor searching and swearing.

PS. I am not a gunsmith :wink:
User avatar
Keachie
.222 Remington
Posts: 333
Joined: Fri Jan 20, 2017 10:21 pm
Favourite Cartridge: .223
Location: Branxholm Tasmania

Re: Winchester 9422 extraction issue

Post by Keachie »

sound like some words of experience there

Sent from my SM-A520F using Tapatalk

User avatar
The Raven
Ultimate AusVarminter
Posts: 5945
Joined: Tue Feb 08, 2011 2:35 pm
Favourite Cartridge: .270 Win
Location: The Cloud

Re: Winchester 9422 extraction issue

Post by The Raven »

Keachie wrote:ImageImage sound like some words of experience there

Sent from my SM-A520F using Tapatalk
Yep, I launched a far few small parts around the house over the years.

Recently spent an hour looking for a carb needle in the grass outside. It LOOKED attached to the float but apparently it was designed to easily fall off when you least expected it.

Couldn’t find it with a magnet (it was ferrous) but finally found it 3ft from where I expected it to have fallen. Only took 45mins.


Sent from my iPhone using Tapatalk
User avatar
Camel
Ultimate AusVarminter
Posts: 12084
Joined: Sat May 28, 2011 8:51 pm
Favourite Cartridge: 20-222 6x47 rem, 250
Location: Northern Riverina NSW

Re: Winchester 9422 extraction issue

Post by Camel »

I would first up try squirting WD40 or similar in to see if it is just gunk that needs washing out, and again maybe after its soaked for a while, give it a blast with compressed air, if the shit can get in, it can usually get out. Might just be a case of needing a good clean out. I have only pulled one 9422 apart, but it was years ago and cant remember any tricks now, know they are more difficult than Marlin lever guns.
User avatar
The Raven
Ultimate AusVarminter
Posts: 5945
Joined: Tue Feb 08, 2011 2:35 pm
Favourite Cartridge: .270 Win
Location: The Cloud

Re: Winchester 9422 extraction issue

Post by The Raven »

Camel wrote: Sat Mar 14, 2020 8:50 pm I would first up try squirting WD40 or similar in to see if it is just gunk that needs washing out, and again maybe after its soaked for a while, give it a blast with compressed air, if the shit can get in, it can usually get out. Might just be a case of needing a good clean out. I have only pulled one 9422 apart, but it was years ago and cant remember any tricks now, know they are more difficult than Marlin lever guns.
Good point. Flushing it out might be an easy fix. WD40 "High Performance Silicone" has a good reputation for rifle cleaning/lube.

Another option, that involves little expenditure, is to get an eBay ultrasonic cleaner (about $25 plus postage). Suitable cleaning liquid recipes are located somewhere on here.

I'm constant amazed at how well it works cleaning up gunked up parts. I used the ultrasonic a while ago to de-rust a bunch of drill bits that had been through a shed fire and subsequent fire hosing. It worked a lot quicker than when I tried to clean them up manually.

FFS why did the first video I look at on Youtube for 9422's take an hour and involve milling machines!!! :shock: :shock: Hardly a quick fix for the average firearm owner.
User avatar
Keachie
.222 Remington
Posts: 333
Joined: Fri Jan 20, 2017 10:21 pm
Favourite Cartridge: .223
Location: Branxholm Tasmania

Re: Winchester 9422 extraction issue

Post by Keachie »

Lol yeah I saw that one aswell.

Will try blasting it out first if nothing else at least I might be a bit less gunked up wen I pull it apart

Sent from my SM-A520F using Tapatalk


Dunderi
.308 Winchester
Posts: 1565
Joined: Sun Sep 28, 2014 10:42 am
Favourite Cartridge: .22-250
Location: Tasmania

Re: Winchester 9422 extraction issue

Post by Dunderi »

Himself is currently sitting at the table, with pieces everywhere, muttering under his breath.

So far he's only pinged one cartridge across the room.

I'd say its going well.
Image

Sent from my SM-G950F using Tapatalk

User avatar
Camel
Ultimate AusVarminter
Posts: 12084
Joined: Sat May 28, 2011 8:51 pm
Favourite Cartridge: 20-222 6x47 rem, 250
Location: Northern Riverina NSW

Re: Winchester 9422 extraction issue

Post by Camel »

I see he has the old model with the spark plug, newer ones use fuel injectors and electronic ignition :lol: :lol:

Good luck with it, make haste slowly. :D
User avatar
The Raven
Ultimate AusVarminter
Posts: 5945
Joined: Tue Feb 08, 2011 2:35 pm
Favourite Cartridge: .270 Win
Location: The Cloud

Re: Winchester 9422 extraction issue

Post by The Raven »

Camel wrote: Wed Mar 18, 2020 7:59 am I see he has the old model with the spark plug, newer ones use fuel injectors and electronic ignition :lol: :lol:

Good luck with it, make haste slowly. :D
I noticed that as well...

All he needs now is a dremel and he can call himself a gunsmith.
Dunderi
.308 Winchester
Posts: 1565
Joined: Sun Sep 28, 2014 10:42 am
Favourite Cartridge: .22-250
Location: Tasmania

Re: Winchester 9422 extraction issue

Post by Dunderi »

Aha!
It was hilarious really, couldn't find a flat blade long handle screwdriver for quids, so he used the stihl tool.

Immediately found 6 big screwdrivers

Sent from my SM-G950F using Tapatalk

User avatar
Camel
Ultimate AusVarminter
Posts: 12084
Joined: Sat May 28, 2011 8:51 pm
Favourite Cartridge: 20-222 6x47 rem, 250
Location: Northern Riverina NSW

Re: Winchester 9422 extraction issue

Post by Camel »

The Raven wrote: Wed Mar 18, 2020 8:22 am
Camel wrote: Wed Mar 18, 2020 7:59 am I see he has the old model with the spark plug, newer ones use fuel injectors and electronic ignition :lol: :lol:

Good luck with it, make haste slowly. :D
I noticed that as well...

All he needs now is a dremel and he can call himself a gunsmith.
And a 4 pound club hammer for those delicate fitting little pieces. :lol:
User avatar
Rabbitz
.338 Lapua Magnum
Posts: 2421
Joined: Sun Mar 25, 2007 9:05 am
Favourite Cartridge: 222
Location: Barossa Valley, SA
Contact:

Re: Winchester 9422 extraction issue

Post by Rabbitz »

Camel wrote: Wed Mar 18, 2020 11:39 am And a 4 pound club hammer for those delicate fitting little pieces. :lol:
I see now where I've been going wrong all these years. Silly me using rawhide hammers and small pein hammers.

I should've listened to my Dad: "Don't hit harder, get a bigger hammer".

:lol: :lol:
User avatar
Keachie
.222 Remington
Posts: 333
Joined: Fri Jan 20, 2017 10:21 pm
Favourite Cartridge: .223
Location: Branxholm Tasmania

Re: Winchester 9422 extraction issue

Post by Keachie »

That is gold Rabbitz

Sent from my SM-A520F using Tapatalk

User avatar
trevort
Spud Gun
Posts: 12710
Joined: Thu Sep 14, 2006 9:21 pm
Favourite Cartridge: Tater
Location: Melbourne

Re: Winchester 9422 extraction issue

Post by trevort »

My bolt action 22 fails to extract after about 100 rounds cause the waxy lube off the lead pills builds up and the cases stick. And then I clean it.

Do you use lead pills with waxy coating?


Sent from my iPhone using Tapatalk
Post Reply