Cleavers for cheap barrels

Gunsmithing & DIY forum for everyone. Enjoy!
Post your projects, questions and advice here.
morerams
New Member
Posts: 86
Joined: Wed Oct 18, 2006 9:09 pm
Favourite Cartridge: 308
Location: Brisbane

Re: Cleavers for cheap barrels

Post by morerams »

Got out to shoot the 6.5x47 today, a bit windy out at Ripley, but never mind. It is one of the easiest barrels I have had to clean, virtually no copper from the first shot. I just used the loads from my previous barrel and at 200yds best group was 19mm worst 31mm with 140 grain Nosler Custom Comp bullets, certainly good enough to buy another barrel or two.
User avatar
Camel
Ultimate AusVarminter
Posts: 12084
Joined: Sat May 28, 2011 8:51 pm
Favourite Cartridge: 20-222 6x47 rem, 250
Location: Northern Riverina NSW

Re: Cleavers for cheap barrels

Post by Camel »

Thats good, I like results like that. :D
User avatar
Tackleberry
.270 Winchester
Posts: 1369
Joined: Mon Jul 29, 2013 4:56 am
Favourite Cartridge: 17HMR
Location: estern vic

Re: Cleavers for cheap barrels

Post by Tackleberry »

Just looking at the cleavers site again looks like all the 224 barrels are prechambered 223r :(
Last edited by Tackleberry on Sun Feb 24, 2019 1:16 am, edited 1 time in total.
User avatar
trevort
Spud Gun
Posts: 12710
Joined: Thu Sep 14, 2006 9:21 pm
Favourite Cartridge: Tater
Location: Melbourne

Re: Cleavers for cheap barrels

Post by trevort »

morerams wrote:Got out to shoot the 6.5x47 today, a bit windy out at Ripley, but never mind. It is one of the easiest barrels I have had to clean, virtually no copper from the first shot. I just used the loads from my previous barrel and at 200yds best group was 19mm worst 31mm with 140 grain Nosler Custom Comp bullets, certainly good enough to buy another barrel or two.

Sounds promising.


Sent from my iPhone using Tapatalk
kickinback
50 BMG
Posts: 3991
Joined: Sun Jan 07, 2007 11:54 am
Favourite Cartridge: 260 Rem
Location: Lilydale Vic

Cleavers for cheap barrels

Post by kickinback »

Tackleberry wrote:Just looking at the cleavers site again looks like all the 224 barrels are prechambered 223r :(
And having seen how they chamber them I’d be avoiding them


Sent from my iPhone using Tapatalk Pro
User avatar
Tackleberry
.270 Winchester
Posts: 1369
Joined: Mon Jul 29, 2013 4:56 am
Favourite Cartridge: 17HMR
Location: estern vic

Re: Cleavers for cheap barrels

Post by Tackleberry »

Plus I need .200" .220" freebore I will ring them tomorrow to see what they got if any blanks ...
Con
.308 Winchester
Posts: 1515
Joined: Thu Sep 14, 2006 11:10 am

Re: Cleavers for cheap barrels

Post by Con »

Tackleberry wrote: Sun Feb 24, 2019 2:10 pm Plus I need .200" .220" freebore I will ring them tomorrow to see what they got if any blanks ...
When I rang they never mentioned pre-chambered. They also mentioned that 338cal barrels can be ordered. I'm tempted by the 6.5mm barrels ... to do another x47 Lapua.
Cheers...
Con
kickinback
50 BMG
Posts: 3991
Joined: Sun Jan 07, 2007 11:54 am
Favourite Cartridge: 260 Rem
Location: Lilydale Vic

Re: Cleavers for cheap barrels

Post by kickinback »

I wouldn’t bother with a prechamber from them. Skip to 8:20

https://youtu.be/LAf064S2Cv4


Sent from my iPhone using Tapatalk Pro
wazza
New Member
Posts: 18
Joined: Fri Sep 19, 2014 9:26 am
Favourite Cartridge: 243

Re: Cleavers for cheap barrels

Post by wazza »

I picked up a 1 in 12 twist barrel they are stamped .223 and are not pre chambered.
I haven't measured it yet to see if that is the bore size or not.
morerams
New Member
Posts: 86
Joined: Wed Oct 18, 2006 9:09 pm
Favourite Cartridge: 308
Location: Brisbane

Re: Cleavers for cheap barrels

Post by morerams »

I got one too, didn't measure the groove diameter but needed a .217" pilot on the reamer, standard .218" wouldn't fit. Good looking barrel, straight and smooth.
User avatar
lee_enfield223
.17 HMR
Posts: 240
Joined: Sun Nov 06, 2016 8:13 pm
Favourite Cartridge: 223rem
Location: sydney

IBI 22 lr barrels any good

Post by lee_enfield223 »

has anybody tried the 22lr barrels for accuracy ????
Post Reply