Buying a new tikka 204r and i am looking for suggestions on the best factory ammo to buy that has good brass for reloading?
Just want to get all the same brass from the start that will last for a fair while.
Cheers for your imput guys
204 brass/ammo
-
trevort
- Spud Gun
- Posts: 12710
- Joined: Thu Sep 14, 2006 9:21 pm
- Favourite Cartridge: Tater
- Location: Melbourne
Re: 204 brass/ammo
so why don't you buy virgin brass and start from scratch
-
Shep25
- .17 HMR
- Posts: 166
- Joined: Sun Jan 28, 2018 6:56 pm
- Favourite Cartridge: .17 remington
- Location: Tailem Bend south australia
Re: 204 brass/ammo
Could do that i guess.
Just figured that doing load development while running it in might throw the groups out a little.
Might be worth looking at though trevort.
Might have to do some 5 shot grouping so i can have a bit of fun while doing it.
Any recommendations on good brass?
Probably start at around 200 pieces.
-
trevort
- Spud Gun
- Posts: 12710
- Joined: Thu Sep 14, 2006 9:21 pm
- Favourite Cartridge: Tater
- Location: Melbourne
Re: 204 brass/ammo
Haven't had a 204 for years so my opinion is old.
Norma makes nice uniform brass but my experience was that it was soft, I lost cases with head expansion and loose primers at lower charges than I would have expected. Its expensive so I wouldn't buy it again. a lot of others would disagree
I did a lot of prep work on the Remington brass and it performed very well. No complaints.
Others may chime in on current brass availability and quality.
lets say it takes you 6 to 10 shots to get your scope zeroed in, clean it and call it run in!!
Norma makes nice uniform brass but my experience was that it was soft, I lost cases with head expansion and loose primers at lower charges than I would have expected. Its expensive so I wouldn't buy it again. a lot of others would disagree
I did a lot of prep work on the Remington brass and it performed very well. No complaints.
Others may chime in on current brass availability and quality.
lets say it takes you 6 to 10 shots to get your scope zeroed in, clean it and call it run in!!
-
grmkc
- .220 Swift
- Posts: 605
- Joined: Tue Oct 14, 2014 5:13 pm
- Favourite Cartridge: 204 Ruger
- Location: Melbourne, Victoria
Re: 204 brass/ammo
Running a Tikka T3 Hunter in the same calibre. Used Hornady 32 & 40 grain Vmax factory ammo with great success in bedding in barrel and now paper and bunny punching. Reusing brass and also bought some new unprimed brass.
Had my first lot of load testing using 40 grain Vmax, AR2219, Hornady brass and RWS primers. Time consuming but fun.
I have narrowed the accuracy down to two distinct loads and will squeeze the specs down tighter in the next couple of months.
Had my first lot of load testing using 40 grain Vmax, AR2219, Hornady brass and RWS primers. Time consuming but fun.
I have narrowed the accuracy down to two distinct loads and will squeeze the specs down tighter in the next couple of months.
-
Shep25
- .17 HMR
- Posts: 166
- Joined: Sun Jan 28, 2018 6:56 pm
- Favourite Cartridge: .17 remington
- Location: Tailem Bend south australia
Re: 204 brass/ammo
Thanks mate.grmkc wrote: ↑Tue Feb 27, 2018 2:56 pm Running a Tikka T3 Hunter in the same calibre. Used Hornady 32 & 40 grain Vmax factory ammo with great success in bedding in barrel and now paper and bunny punching. Reusing brass and also bought some new unprimed brass.
Had my first lot of load testing using 40 grain Vmax, AR2219, Hornady brass and RWS primers. Time consuming but fun.
I have narrowed the accuracy down to two distinct loads and will squeeze the specs down tighter in the next couple of months.
I was thinking maybe Hornady as they are readily available.
Although this will be my first rifle i am looking forward to doing load development.
My Tikka will be a synthetic T3x in varmint as suggested by a few on this site.
Cheers Bob