i would like to know what your using to fl size your cases.
i just got a simplex vise type for 308.
ive done 7 cases and my hands are ready to drop off from the vice handle.
are these things supposed to be that hard ?
im using graphite powder to lube,after trying one case with case lube.[both just as hard]
the liquid lube was cleaned out before the powder was used btw.
sean.
what fl sizer are you using ?
- Camel
- Ultimate AusVarminter
- Posts: 12084
- Joined: Sat May 28, 2011 8:51 pm
- Favourite Cartridge: 20-222 6x47 rem, 250
- Location: Northern Riverina NSW
Re: what fl sizer are you using ?
Had one of those vice type FL dies years ago for a 222, I used to bash them in with a plastic mallet, didn't have a vice, worked ok but took a lot of elbox grease. I now use proper dies in a Redding T7 Turret press for when I FL using dies from a few different manufacturers.
-
- .338 Lapua Magnum
- Posts: 3256
- Joined: Wed Sep 26, 2007 10:47 pm
- Favourite Cartridge: N/A
- Location: Im here...
Re: what fl sizer are you using ?
Whidden gunworks FL bushing dies in a Lyman crusher. Redding imperial sizing wax is great stuff.
- stinkitup
- .338 Lapua Magnum
- Posts: 3217
- Joined: Fri Aug 03, 2007 10:46 am
- Favourite Cartridge: 6.5x55
- Location: Lower Hunter Valley
Re: what fl sizer are you using ?
Lee and Redding dies and Lee Press never needed that much elbow grease! Even their hand press can do swede cases no drama.
Ryan
Ryan
- trevort
- Spud Gun
- Posts: 12710
- Joined: Thu Sep 14, 2006 9:21 pm
- Favourite Cartridge: Tater
- Location: Melbourne
what fl sizer are you using ?
Body dies mainly but on rate occasions
-
- .22 WMR
- Posts: 131
- Joined: Fri Dec 15, 2006 9:15 am
- Location: Wagga Wagga, NSW.
Re: what fl sizer are you using ?
I use a Redding Body die for my 308,if I have a batch of once fired cases,fired from different rifles,ex rifle club brass,I use a Lee Full Length die in a Redding 7/8 X 14 press.For lube I use anhydrous lanolin or Lanotech grease.
In the past I used a Simplex vice die,with a solid 6" vyce,found it easy to use,but slow.At the time I used normal chassis grease for lube.Try sizing not all the way down,just enough for the cases to fit the rifle.A flat washer or two on the head of the die should do it if your die is on the short size.To remove the case I put a 5/8" nut on the case head end and pushed the case out with the vyce.Hammering seemed too drastic for me.
Probably not applicable in your case,but make sure the threads of the vyce are clean and well lubricated also.
Mike
In the past I used a Simplex vice die,with a solid 6" vyce,found it easy to use,but slow.At the time I used normal chassis grease for lube.Try sizing not all the way down,just enough for the cases to fit the rifle.A flat washer or two on the head of the die should do it if your die is on the short size.To remove the case I put a 5/8" nut on the case head end and pushed the case out with the vyce.Hammering seemed too drastic for me.
Probably not applicable in your case,but make sure the threads of the vyce are clean and well lubricated also.
Mike
- mick_762
- 50 BMG
- Posts: 4156
- Joined: Sun Mar 04, 2012 1:46 pm
- Favourite Cartridge: 308 Norma
- Location: Wodonga Vic
Re: what fl sizer are you using ?
Forster for the .308 and .243
Redding body die too for use prior to that when needed.
Redding for the .308 Norma and the 9.3x62
Simplex for the 30-30
Lee collet for the .222
Mick
Redding body die too for use prior to that when needed.
Redding for the .308 Norma and the 9.3x62
Simplex for the 30-30
Lee collet for the .222
Mick
-
- .222 Remington
- Posts: 304
- Joined: Sun Jan 05, 2014 11:18 pm
- Favourite Cartridge: 223
- Location: Southwest WA
Re: what fl sizer are you using ?
Forster for nearly all the common calibers
Redding for all the ones forster don't do
Whiddens and my own ones for custom stuff.
Redding for all the ones forster don't do
Whiddens and my own ones for custom stuff.
- Seddo
- .338 Lapua Magnum
- Posts: 2054
- Joined: Sat Jan 03, 2009 9:17 am
- Favourite Cartridge: Creedmoor
- Location: Vic
Re: what fl sizer are you using ?
many types.
Redding S Type (where possible)
Redding FL
Hornady FL
Lee FL
sold my forster set last week.
Redding S Type (where possible)
Redding FL
Hornady FL
Lee FL
sold my forster set last week.
- Rigpig
- New Member
- Posts: 66
- Joined: Sat May 23, 2015 10:35 am
- Favourite Cartridge: 45-70
- Location: WA
Re: what fl sizer are you using ?
I have lee for the 223
RCBS and Redding for the 30-30
RCBS for the 308
I started with a small RCBS press was hard work so I purchased a lee press now love it I use RCBS lube too much makes it hard to pull out again
RCBS and Redding for the 30-30
RCBS for the 308
I started with a small RCBS press was hard work so I purchased a lee press now love it I use RCBS lube too much makes it hard to pull out again