CZ 465 with double triggers - conversion to single trigger

[barryb]

Wondering if anyone has ever had this done & if so just what was involved in the process , approx. cost etc .
Thanks for any info
BarryB

[Camel]

I have seen a couple of threads on Saubier about this topic mate, also when I asked on here some years ago, I was informed that some Timney Mauser 98 triggers could be made to fit. I don't know how or what modifications would need to be done to the lower trigger housing on them. Maybe just a matter of opening the trigger opening in the trigger housing and then a bit of dremel work to either thin down the ears on the trigger itself, or widening the gap inside to fit the trigger in.

[stinkitup]

I have been doing a lot of research on this but for my 527 with doubles.

A timney m98 will work bit you have to remove some of the trigger guard metal I have some pics I will put up later.

[barryb]

Thanks Camel & Stinkitup - very much appreciated. Seems it may not be mission impossible & bankroll breaking.

[Camel]

You will have to get up to date on your rifle models mate, its a Brno, not CZ

[stinkitup]

http://www.ausvarmint.com/forum/viewtopic.php?t=17450

This is my link think there are some photos.

where abouts are you again?

[stinkitup]

You will have to get up to date on your rifle models mate, its a Brno, not CZ

Well mine is stamped both!

[stinkitup]

You will have to get up to date on your rifle models mate, its a Brno, not CZ

Well mine is stamped both!

[stinkitup]

Stupid phone

[Camel]

Bit of difference mate, yours isn't a ZKW465, you know, when Brno really knew how to build a proper rifle.

[stinkitup]

Bit of difference mate, yours isn't a ZKW465, you know, when Brno really knew how to build a proper rifle.

This is your sitting in the safe right?? Or is it in use yet Not that mine is copping much work lately

Okay back on Track Barry

Of the two photos below the section in orange will need removing and all the trigger mech and the top hanger/sear part, I thought filing might work but a smith I contacted from Norway doing these said he mills them and some are very hard but appears to be very thin so think it still could be done here at home. I have checked mine against a m98 normal trigger thanks to camel, next is to pull my m96 swede trigger out and check them out a bit more. Need to pull everything out and make sure it hanges off the action with no changes required then if it is just this piece it would be easy.

527_double_trigger.jpg (129.88 KiB) Viewed 996 times

527_double_trigger_2.jpg (130.15 KiB) Viewed 996 times

[Aussie steve]

I have a zkw 465 with a single trigger. It works a treat, I much prefer it to double set triggers.

[Camel]

I have a zkw 465 with a single trigger. It works a treat, I much prefer it to double set triggers.

Hey Steve, I remember some time ago you mentioned that, whats the chance of putting up a photo or two, similar to Ryan so we can have a look ? There seems to be a fair few interested.

[stinkitup]

I have a zkw 465 with a single trigger. It works a treat, I much prefer it to double set triggers.

Hey Steve, I remember some time ago you mentioned that, whats the chance of putting up a photo or two, similar to Ryan so we can have a look ? There seems to be a fair few interested.

Yep or else your just rubbing it in lol

Where abouts are you Aussie Steve? NSW somewhere?

I think it is an easy enough job will be trying to do this conversion later this year.

[Branxhunter]

Like this?

image.jpg (50.1 KiB) Viewed 960 times

Marcus