Page 4 of 5
Re: In the beginning....
Posted: Sat Apr 18, 2020 8:06 pm
by dashooter
Branxhunter wrote:So did you grind the recoil pad down, or did Russell? How was it done?
I mount my belt sander upside down in the bench vise. Agricultural but seems to work - would be the perfect method for a Zasty
Marcus
Russell’s bench grinder mounted normally. I’m ashamed to say I pleaded ‘the Trev’ with that one and my fingers so Russell did it.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Tue May 12, 2020 9:26 am
by dashooter
Oiling is coming along nicely. Might be done by this weekend.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Tue May 12, 2020 10:58 am
by mick_762
That's looking very nice Rob
Re: In the beginning....
Posted: Tue May 12, 2020 11:07 am
by Camel
Classy work on a classy stock on a classy rifle, looking very nice mate
Re: In the beginning....
Posted: Tue May 12, 2020 10:13 pm
by dashooter
mick_762 wrote:That's looking very nice Rob
Thanks Dave. A little bit to go.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Tue May 12, 2020 10:14 pm
by dashooter
Camel wrote:Classy work on a classy stock on a classy rifle, looking very nice mate
Thanks Mark.
Will look a bit odd once I put the scope on it. Not traditional at all. Lol
Sent from my iPhone using Tapatalk
In the beginning....
Posted: Sun May 17, 2020 11:16 am
by dashooter
Finally done.
Now to wait for the range to reopen to sight it in.
Since when does Tapatalk have a monthly image upload limit!?
Apparently I’ve reached my limit without subscribing.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Sun May 17, 2020 12:41 pm
by Branxhunter
That has come up well. It's a bit hard to tell for sure but does the top line of the forend almost meet the top line of the barrel contour? Does the stock top line need to be taken down a little?
It sounds like you are going to install one of your thermo scopes on it?
Marcus
Re: In the beginning....
Posted: Sun May 17, 2020 12:45 pm
by Camel
Branxhunter wrote: ↑Sun May 17, 2020 12:41 pm
That has come up well. It's a bit hard to tell for sure but does the top line of the forend almost meet the top line of the barrel contour? Does the stock top line need to be taken down a little?
Marcus
It does look that way, but if you look at the action, I think the front is bedded deeper than the rear
Easy fix, just raise the barrel at the tip of the fore end, then re bed so it is even.
But then it could be an optical delusion.
P.s., it does look rather nice though Rob.
Re: In the beginning....
Posted: Sun May 17, 2020 2:40 pm
by dashooter
Not sure but I think it’s level.
Certainly the inletting around the top section is level between the front and rear sections of the mounting area for the rail. Not sure why it looks out across the entire length though.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Sun May 17, 2020 6:46 pm
by dashooter
Branxhunter wrote:That has come up well. It's a bit hard to tell for sure but does the top line of the forend almost meet the top line of the barrel contour? Does the stock top line need to be taken down a little?
It sounds like you are going to install one of your thermo scopes on it?
Marcus
It does look a bit deep.
Yep, will be getting a run with the 4K pro on top.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Mon May 18, 2020 9:44 am
by trevort
Re: In the beginning....
Posted: Mon May 18, 2020 11:14 am
by dashooter
Describe away Trev. I won’t be offended either way. Others however may pick.
My biggest issue in fitting the action was getting it deep enough without being set too far below the woodwork and being able to get the magazine release to work constantly without having to jiggle things around with my tongue hanging out the corner of my mouth. I settled for the lesser of two evils (in my mind).
Once I got the action deep enough for that to work it was more a case of finishing and oiling than worrying too much about where the barrel sat within the forend (and obviously making sure it was floated).
If I had a workshop (and more skills)I could probably have worked on it a bit more to get it looking more normal.
Sent from my iPhone using Tapatalk
Re: In the beginning....
Posted: Mon May 18, 2020 1:05 pm
by Camel
dashooter wrote: ↑Mon May 18, 2020 11:14 am
Describe away Trev. I won’t be offended either way. Others however may pick.
What ever do you mean ? No one ever picks on Trevort.
Re: In the beginning....
Posted: Mon May 18, 2020 6:33 pm
by kickinback
dashooter wrote:Finally done.
Now to wait for the range to reopen to sight it in.
Since when does Tapatalk have a monthly image upload limit!?
Apparently I’ve reached my limit without subscribing.
Sent from my iPhone using Tapatalk
Photo whore. To many tasty grub pics
Sent from my iPhone using Tapatalk Pro