6mm ????????

kickinback · Post by **kickinback** » Sun Jun 30, 2019 9:27 pm

Don’t worry about it. It’ll turn up.

Maybe

Sent from my iPhone using Tapatalk Pro

Camel · Post by **Camel** » Tue Jul 09, 2019 7:17 pm

Dies and brass turned up yesterday in the mail, thanks to Ned Kelly and the VRA

Getting closer to the completion now.

Camel · Post by **Camel** » Thu Jul 11, 2019 9:57 am

Seems that I am at the final straight in the race to get my trigger from Brownells, this received this morning:

Following goods have arrived in the Australian Warehouse for processing :
Line# Order No. Part No. Name Date Arrived In Warehouse
1 BRA47170 758000023 WEATHERBY/HOWA/S&W/ 10/07/2019 02:54:06 PM

We will update you again when these are dispatched to you.

Camel · Post by **Camel** » Thu Jul 11, 2019 10:02 am

Camel wrote: ↑Wed Jun 26, 2019 11:51 am Fitted rail this morning

Rear screws nipped up tight, and turns out the front is floating two thicknesses of thin cardboard, problem ?? Advice greatly accepted

I haven't touched this since I tried it on a couple of weeks ago, and I have started wondering if when they build these rail thingos, is the 20moa achieved by screwing the front down to be in contact with the front receiver ring, and these rails really have no taper on them, just need to be bent to achieve the desired results. Thoughts ????

kickinback · Post by **kickinback** » Thu Jul 11, 2019 12:49 pm

I’ll take a pic of mine for you after I finish servicing the hilux

Sent from my iPad using Tapatalk Pro

Flash Gordon · Post by **Flash Gordon** » Thu Jul 11, 2019 2:53 pm

Take it to Darren.

Camel · Post by **Camel** » Fri Jul 12, 2019 11:12 am

Well, I have to say, once they had it in their warehouse in Aust, they haven't mucked around sending it out here.
Got this notification from Brownells this morning:

Your Order has been Shipped from Brownells Australia please find the attached invoice copy.

Camel · Post by **Camel** » Fri Jul 12, 2019 11:13 am

Flash Gordon wrote: ↑Thu Jul 11, 2019 2:53 pm Take it to Darren.

If, after I get it together and something doesn't quite gel I will be giving him a visit.

kickinback · Post by **kickinback** » Fri Jul 12, 2019 1:24 pm

Mine fits nicely

Sent from my iPhone using Tapatalk Pro

Rabbitz · Post by **Rabbitz** » Fri Jul 12, 2019 1:44 pm

Camel wrote: ↑Thu Jul 11, 2019 10:02 am I haven't touched this since I tried it on a couple of weeks ago, and I have started wondering if when they build these rail thingos, is the 20moa achieved by screwing the front down to be in contact with the front receiver ring, and these rails really have no taper on them, just need to be bent to achieve the desired results. Thoughts ????

Surely a couple of quick measurements with a micrometer or vernier will answer the question.

One end would be thicker than the other?

Also you didn't mount it backwards per chance?

Camel · Post by **Camel** » Fri Jul 12, 2019 1:58 pm

Rabbitz wrote:
Camel wrote: ↑Thu Jul 11, 2019 10:02 am I haven't touched this since I tried it on a couple of weeks ago, and I have started wondering if when they build these rail thingos, is the 20moa achieved by screwing the front down to be in contact with the front receiver ring, and these rails really have no taper on them, just need to be bent to achieve the desired results. Thoughts ????
Surely a couple of quick measurements with a micrometer or vernier will answer the question.

One end would be thicker than the other?

Also you didn't mount it backwards per chance?

Batt flat in calipers, it’s a bugger as I can’t get one here and not worth 220km round trip to get one, keep forgetting when in the big smoke,and no not b. t. f.

DSD · Post by **DSD** » Fri Jul 12, 2019 9:47 pm

Camel wrote:
Rabbitz wrote:
Camel wrote: ↑Thu Jul 11, 2019 10:02 am I haven't touched this since I tried it on a couple of weeks ago, and I have started wondering if when they build these rail thingos, is the 20moa achieved by screwing the front down to be in contact with the front receiver ring, and these rails really have no taper on them, just need to be bent to achieve the desired results. Thoughts ????
Surely a couple of quick measurements with a micrometer or vernier will answer the question.

One end would be thicker than the other?

Also you didn't mount it backwards per chance?
Batt flat in calipers, it’s a bugger as I can’t get one here and not worth 220km round trip to get one, keep forgetting when in the big smoke,and no not b. t. f.

What battery does it take?

Sent from my SM-G930F using Tapatalk

Camel · Post by **Camel** » Sat Jul 13, 2019 8:14 am

One of those little button type things, dunno what number

DSD · Post by **DSD** » Sat Jul 13, 2019 8:36 am

If it's a 2032(very common) I could walk up to the shop buy 1 and post it to you or

https://www.ebay.com.au/itm/CR2032-Butt ... bRlMPyUHgg
Not so hard.

Sent from my SM-G930F using Tapatalk

trevort · Post by **trevort** » Sat Jul 13, 2019 9:33 am

It’s hard for dumb bactrians

Sent from my iPhone using Tapatalk

AusVarmint

6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????

Re: 6mm ????????